2/11/2024 0 Comments Ac opto isolator supplierShipping Weight: 0.5 pounds (0.22 Kg) packed.Copy to Clipboard Download file Figure 1: A common opto-isolator contains an LED and a bipolar phototransistor. I/O Connectors: Removable plug-in type terminal blocks rated for 12A/250V AWG #26-12, stranded/solid copper wire. General purpose NEMA Type 1 enclosure.Ĭircuit Board: Military grade fire-retardant epoxy glass per IPC-4101/98 with humi-seal conformal coating. General: General purpose plastic enclosure for mounting on 35mm “T-type” DIN rail.Ĭase Material: Self-extinguishing polyamide, UL94 V-0 rated, color light gray. ATEX Certified.ĭesigned for Class I Division 2 Groups ABCD Zone 2. Inputs isolated from each other (channel-to-channel) and from output/power.Įlectromagnetic Compatibility (EMC) ComplianceĬE compliant. Power Supply Effect: Less than ☐.001% of output span effect per volt DC of supply change. Current draw varies with power voltage as follows (current indicated is with all outputs ON). Power Requirement: 12–32V DC SELV (Safety Extra Low Voltage). Relative Humidity: 5 to 95% non-condensing. Note: Do not exceed 150mA of drain current per output channel. If a stronger pull-up (lower resistance) is required, a resistor will have to be wired externally in parallel with the output channel. Output Pull-ups: Individual output channels include 1KΩ pull-ups to the internal +5.3V DC rail. Output Response Time: 45ms, typical (measured from input transition to output). Output Rds On Resistance: 2.5 ohms, maximum (150mA, 85☌). Output “ON” Current Range: 0 to 150mA DC, continuous, each channel. Output Pull-Ups: 1KΩ pull-ups to 5.3V DC. Output “OFF” Leakage Current: 1♚ typical, 50♚ maximum (mosfet only, 25☌, 32V DC). Output “OFF” Voltage Range: 0-32V DC maximum. Output channels are pulled up to +5.3V with 1KΩ resistors. Low-side (sinking) switching between load and return for DC voltage and current-sinking applications only. Output Type: Six open-drain, mosfet switches with a common source connection at output return. Input channels also include capacitive filtering, and series resistance. Rated Continuous Voltage: 130Vrms, 130V DC. Input Over-Voltage Protection: Metal Oxide Varistors (MOV) at every channel input. High-to-Low threshold: 60V AC (55V DC), typical. Low-to-High threshold: 90V AC or DC, typical. Input Signal Voltage Range: 0-130Vrms or ☑30V DC. Built-in hysteresis provides a sensing threshold for monitoring mains power. Input Type: Six individually isolated voltage inputs interface voltage levels. XTA-120V-6: Solid-State Relay Input Modules Performance Specifications Input Output Ranges: Open-drain: 1KΩ pull-up to +5.3V DC, 0-32V DC maximum, 150mA sink. These units are ideal for remote monitoring, distributed control, or SCADA applications. Rugged construction and high density design combine for a very effective I/O solution. Removable front-facing terminal blocks on the module’s top and bottom greatly simplify field wiring. Opto-isolators control an open-drain output to safely interface the status of the monitored signal. It is intended for use with BusWorks XT Series discrete I/O and other digital input modules to monitor contact closures or mains power supply high/low voltage levels.Įach channel senses the presence or absence of high-level voltage to determine the status of proximity switches, limit switches, toggle switches, push buttons, contacts, and other devices. The XTA-120V-6 optocoupler module provides six individually isolated 120V AC/DC digital (discrete) inputs to sense on/off levels and drive open-drain outputs. XTA-120V-6: Solid-State Relay Input Modules Description
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |